Popular Articles

  1. Lutron Unified Module with RadioRA3 and Homeworks QSX

    Last Updated: 08/09/2023 in Accelerator 3 3rd Party Information & Troubleshooting
    Application Note: When integrating with RadioRA3 and Homeworks QSX (Not QS), you only need to use the Lutron Unified Control Two-Way Module . It is not necessary to use the Lutron Telnet Expansion Two-Way Module at all ( https://urcportal.com/M...

  2. DMS-AV: Lipsync Delay

    Last Updated: 10/05/2016 in Total Control: Accelerator 1 & 2 DMS-AV
    Audio/Video delay (Lip-Sync Delay) with a DMS-AV Symptom: A lip sync delay when selecting a source from the DMS-AV . Solution:   There are two possible solutions to correct a lip sync delay. Select Step 8...

  3. Converting Audio Files for Use In An HDA System

    Last Updated: 10/17/2023 in Accelerator 3 HDA
    URC HDA devices and software provide countless options to configure and optimize audio settings to achieve performance and flexibility for almost any application. The following article provides information related to c onverting .mp3 files to ...

  4. Lost Program After Changing Batteries MX-900, MX-450, MX-350

    Last Updated: 07/07/2022 in Complete Control
    Symptom : Replaced batteries in the remote and lost  the   programming.  This can occur in the MX-350 , MX-450 and MX-900 .  If this happens please follow the steps below: Solution: Remove all the batteries  from the remote and let it ...

  5. How to Adjust the High DPI Settings When Using a 4K or Hi-Resolution Screen

    Last Updated: 06/09/2021 in Total Control: Accelerator 1 & 2 Software Settings
    How to Adjust the High DPI Settings When Using a 4K or Hi-Resolution Screen It is possible when using a 4K or high-resolution display or laptop, you may need to adjust the High DPI scaling for best performance when using and viewing the URC Accel...

  6. Manually Configuring the Advanced (Network) Settings for Gigabit Ethernet-enabled URC Devices

    Last Updated: 07/10/2023 in Accelerator 3 Software Settings
    Specific URC devices connected to advanced networking gear can sometimes cause issues when discovering and/or downloading during the programming process. If you are having issues discovering a device from within Step 6b: URC Devices, or the device ...

  7. Using HDA Audio with a L-Acoustics LS10 AVB Network Switch

    Last Updated: 05/03/2022 in Accelerator 3 HDA
    URC HDA devices and software provide countless options to configure and optimize audio settings to achieve performance and flexibility for almost any application. In most cases, the URC HDA-SW5 switch capacity is sufficient for most installations. ...

  8. Using a Third-Party AVB Switch in an HDA System

    Last Updated: 06/09/2021 in Accelerator 3 HDA
    URC HDA devices and software provide countless options to configure and optimize audio settings to achieve performance and flexibility for almost any application. The following article details a few factors to consider when determining what AVB s...

  9. Setting Up Microphones on the HDA-1600 Amplifier

    Last Updated: 06/09/2021 in Accelerator 3 HDA
    URC HDA devices and software provide countless options to configure and optimize audio settings to achieve performance and flexibility for almost any application. One of those features is the flexibility of the HDA-1600  amplifier and the microph...

  10. How To Determine The Stream Number of Your Source

    Last Updated: 05/10/2016 in Total Control: Accelerator 1 & 2 DMS-AV
    The DMS Devices (DMS-AV/DMS-100/DMS-1200) all have a certain number of streams. All of the available streams can be selected when creating custom macros. The following depicts how to determine the stream number of your source as wel as use it in a m...